金年会 金字招牌诚信至上,金年会 金字招牌诚信至上,金年会 金字招牌诚信至上,金年会 金字招牌诚信至上

How to compare medium frequency pipe bender manufacturers

How to compare medium frequency pipe bender manufacturers

Comparison of medium frequency pipe bender manufacturers:The company mainly produces middle frequency pipe bending machine has more than 20 years of production experience, in the process of the production of intermediate frequency pipe bender can manufacture according to the requirements of different types and materials of intermediate frequency pipe bending machine, intermediate frequency to buy advantage of pipe bender is, model complete, price concessions, who buy our company's customer intermediate frequency pipe bender,Our company will complete the manufacture of intermediate frequency pipe bender within the time agreed by the customer.

Before operation, the medium frequency pipe bender shall first check whether the lubrication points are short of oil, whether the movement structure is loose, and whether the protective equipment is installed. After confirmation, the operation shall be carried out.In the operation process of medium frequency pipe bender, whether the system pressure is maintained within the specified range, damage to the hydraulic components, whether it will be affected in the operation project.Adjust the necessary position and Angle of the parts.Adjust the positioning of the parts to the required length, adjust the vertical lifting guide rail, is a guide mold pressing cylinder can be added into the iron pipe.Adjust the vertical lifting guide rail, the guide rail mold pressing cylinder can travel tight iron pipe.The above introduction in the factory of the medium frequency pipe bender when our installation personnel will be in the debugging and installation process will slowly provide the above process to order the customer of the medium frequency pipe bender.Let the customer use in the operation process at ease.

After the above simple introduction and the detailed introduction of our company's engineers before ordering, you should have a detailed understanding of the intermediate frequency I hang up the machine.If you have anything else to compare with the medium frequency pipe bender our engineers and sales staff welcome your comparison and inquiry.Welcome friends around the world to consult 24 hours a day.

The intermediate frequency pipe bender features custom-made operation by workers

The company mainly produces all kinds of pipe fittings equipment, in which, when the pipe bending machine twists and turns, the wind pipe elbow machine is pulled forward by the pipe because of the car as the load. In order to innovate the twists and turns, the wall thickness of the pipe twists and turns is extreme and thin, and the rebound is reduced, and the boosting equipment is increased.In zigzag, the die not only compresses the pipe, but is pushed forward by an auxiliary thrust to form a side thrust for bending.The bending arm and the winding spindle are connected together, the bending die shaft of the bending pipe can be replaced, and the clamping die can be moved up and down. The air pipe elbow machine not only has a reasonable structure, but also increases the strength of the machine, and the structure is general, so that the electrical circuit is simplified.

Correct control of the pipe bender can be roughly customized according to the operator's person, and is very conducive to extending the service life of the pipe bender.The bending pipe not only prevents the trolley from colliding with the pressing die to complete the bending machine smoothly, but also can probably reduce the loss of clamping of the material head and reduce the production cost.

Medium frequency pipe bender has the following characteristics:

1) The process can stop the traditional bending process forming, the convex edge of the pipe wall is pulled and thinned, and the concave edge of the pipe wall is compressed and thickened, which results in the uneven thickness of the bending pipe wall.

2) The small radius (R≈D) and thin wall (t/D≈0.015) 180 elbow with uniform wall thickness can be produced by adopting this process, which cannot be achieved by other bending process.

3) If all kinds of process parameters are planned reasonably, the process can ensure that the thickness of the pipe wall at all parts is always connected and stable during the forming process of the elbow, that is, the thickness of the straight pipe wall before deformation is non-stop.

4) The process can be adopted to push the same caliber 45, 90, 180 and other bending angles in the same horn mandrel at the same time, and the production is high.

2295-2292.