金年会 金字招牌诚信至上,金年会 金字招牌诚信至上,金年会 金字招牌诚信至上,金年会 金字招牌诚信至上

Introduction to the maintenance of tee equipment

Introduction to the maintenance of tee equipment

The three-way machine equipment needs to be maintained in accordance with the corresponding maintenance standards. Even if the operation is simple, the three-way machine also needs to be maintained and nursing, so as to fundamentally prevent mechanical failure and ensure the smooth progress in the production process.

Tee machine equipment in the production process, found that severe wear and tear parts to be replaced, regular protection personnel to the three machinery maintenance and protection, such as adding lubricating oil, etc.Finally, in the sliding side in the production process of smooth manufacturing and production of three-way pipe fittings, so as not to prevent the oxidation and rust of the three-way machine, especially in the case of long-term idle, do a good job in the maintenance of details, the normal work of the three-way machine equipment is very good, together also can ensure the smooth production.

In the daily maintenance process, it is important to be careful, whether it is about all the work of the three-way machine equipment, or about the replacement of some parts, it is necessary to regularly check the wear situation, especially in the production process, pay more attention to these parts, in order to prevent severe wear and tear from affecting the production process.If the manufacturer of three-way machine wants to reduce the wear of parts as far as possible, and does not affect the production together, three-way machine equipment downhill forming can significantly reduce the marginal extension.

Tee machine molding operation, increase the quantity of the open pass, is slightly less than the thickness of roll gap between the upper and lower roller, namely the central tube billet by trace calender, an extension of the larger in the central, to reduce the relative elongation of the marginal if central extension is greater than the marginal extension, is now at the exit twist up, if less than the marginal extension, is winding down, adjust the operation should be flat as well.The central extension adds the deformation of the forming machine, so that the power consumption is added, the roller wear is severe, the equipment is simply damaged, and when the tube billet and the roller surface have a relative slide, the roll marks and scratches simply occur.The three-way machine increases the weight of the roll, which increases the length of the deformation zone of the frame. The marginal extension is inversely proportional to the length of the hole deformation. If possible, try to increase the diameter of the roll, which can reduce the marginal extension.Tube billet marginal variant by squeeze force between the rack, when the frame from the larger, in the marginal extension necessary by the end of each frame boundary frame frame squeeze and absorption, easy cause bulge, shorten the distance, also is essentially to add frame number, each frame will be tight marginal extension freely and absorb, improved the processing conditions, but from too small,It is necessary to leave sufficient operating space.

Quality assurance and characteristics of three - way machine manufacturers

The company is three machine quality assurance, reasonable price, save time and effort, the company to the whole service, three machine long service life.Simple operation, high production efficiency.In recent years, our factory has studied and improved the synchronization performance of both sides of the cylinder piston of the tee machine equipment. The synchronization error has been reduced from 5-10 to 0.5, which has brought a new way to reduce the cost for the bank.

The tee machine is mainly a machine for making T tees. The tee is divided into equal diameter tee and reducing tee.Tee machine in the production of equal diameter tee and reducing tee is mainly used for the stability of water pressure, we use a pressure balance to stabilize the water pressure in the steel pipe extrusion tee, is the steel pipe in the extrusion process to maintain a constant pressure, so as to achieve a higher yield.

Three - way machine is the machine that makes three - way, three - way refers to metal three - way.Whether carbon steel, alloy steel, stainless steel, or titanium alloy is no problem.

There are three kinds of machines to make a tee, one is hot drawing tee machine, hot pressing tee machine, connecting tee machine.

It is characterized by low cost, but the pull out outlet is not high enough, and a section of steel pipe needs to be welded.

Tee machine, this process first I made a tee with larger wall thickness than SCH80 tee.

Cold extrusion tee machine is also a common way to make tee. Now the scale of making tee is 21-630 and the thickness is 3-20mm. All the above models can be made by our cold-extrusion concave lens.Cold extrusion tee machine is mainly characterized by high efficiency, low rate of defective products, reasonable price, generally a molding.

The main power of the three-way machine is the hydraulic cylinder. The body of the three-way machine belongs to the non-standard product, so there is no specific specification and model. We can directly customize the cold extrusion three-way machine according to the customer's requirements.

Three machine manufacturers mainly according to the requirements of customers to manufacture different types of three machine, welcome three machine users to inquire.

2254-2231.